ความต้องการการติดตั้งและการระวังความปลอดภัยของเครื่องชั่งสแตนเลสเหล็กลวด

ความต้องการการติดตั้งและการระวังความปลอดภัยของเครื่องชั่งสแตนเลสเหล็กลวด

สินค้า

The stainless steel wire drawing machine is mainly used for the surface treatment of metal. The ss wire drawing machine adopts physical properties to polish the workpiece while keep the performance of the workpiece does not change at the same timed. For stainless steel wire drawing machine, the following requirements need to be met during the installation and use:


Installation and Use Requirements of Stainless Steel Wire Drawing Machine


  • The installation foundation of the stainless steel wire drawing machine must be very stable and avoid vibrating.


  • Before starting the machine, check the air supply and circuit conditions of the stainless steel wire drawing machine to see if there is any air leakage and water accumulation. Install the abrasive belt of the stainless steel wire drawing machine correctly, and the lubrication level of the lifting screw of the upper and lower shafts should be tested.  Make sure that there is no one on the discharge, and then the machine can be turned on.


  • Avoid frequent starting and stopping during the use, which will affect the drawing effect and increase the wear of the drawing die.


  • In the process of using stainless steel wire drawing machine, operators shall not leave their jobs at will, so as to avoid accidents.


  • Gloves must be worn when the stainless steel wire drawing machine is operating, because the workpiece will generate high temperature during wire drawing. Wearing gloves can prevent your finger burn and avoid affecting the surface quality of the product.



Precautions for the Use of SS Wire Drawing Machine


  • Check whether the lubrication level of each lubricating point is in right places, whether the pressure of the water and gas lines is within the qualified range, and whether there is a falling wire rack on the trolley. Then pull the wire rack and the trolley to the designated positions, put down the pulling claw, and connect it with the pulling claw.


  • Turn on the power and let the AC main motor run without load for a certain period of time. Place the wire drawing die into the die box of the stainless steel wire drawing machine, and thread the wire that has been nearly tipped in advance into the mold, or pull it into it with a wire drawing pliers and press it tightly. Hang the other end of the wire drawing pliers directly above the reel. Then turn on the speed regulation, and let the drum rotate slowly for 10 to 20 turns with the traction wire. Metal Tech is a steel wire drawing machine manufacturer who has various types of wire drawing machine for sale, including machines for straight line wire, wheel type wire, water tank wire, vertical type wire, and so on. Welcome to contact us for steel wire drawing machine price list.


  • Remove the wire drawing pliers and withdraw the wire for two to three turns. Manually control the air valve, and let the wire pressing roller press the wire on the reel tightly. Pull the previously withdrawn wire to the drop frame superior. Then start the host at a slower speed, and gradually increase the speed, and the stainless steel wire drawing machine can enter the working state normally. Here we provide a ss wire drawing machine introduction video for you to get better understanding of it.


  • When the stainless steel wire drawing machine is working under the normal state, there should be no personnel working under the equipment. When the drop frame is full of wires, the ss wire drawing machine will be stopped immediately. Manually control the air valve to release the pressing roller, push out the trolley, lift all the wires on the drop frame, and finally push the trolley in to work again.

บทความอื่นๆของเครื่องจักรลวดและลวดตาข่าย

  • การแต่งกลับที่เตาอบแบบเนื้อเห็ดการแต่งกลับที่เตาอบแบบเนื้อเห็ดMarch 13, 2023ไม่มีข้อความที่ต้องแปล เนื้อหาข้างต้นเป็นคำสั่งฉบับภาษาอังกฤษ เพื่อให้ผู้ใช้งานคำนวณจำนวนคำหรือค้นหาข้อมูลเพิ่มเติม กรุณาเติมข้อความตัวอักษรที่ต้องการแปล ขอบคุณค่ะview
  • เครื่องทอผ้าลวดรูปหกเหลี่ยมเป็นเครื่องจักรที่แข็งแรงและทนทานเครื่องทอผ้าลวดรูปหกเหลี่ยมเป็นเครื่องจักรที่แข็งแรงและทนทานNovember 24, 2022เครื่องทองหลางลวดหกเหลี่ยมใช้ในการผลิตโลหะแบบลวดหกเหลี่ยมปกติ เราจะให้คุณทราบเกี่ยวกับความรู้ทั่วไปเกี่ยวกับเครื่องทองหลางลวดหกเหลี่ยม ในความเป็นจริง เครื่องทองหลางลวดหกเหลี่ยม...view
  • ชนิดของเครื่องดึงเส้นผ่านหน้าแหล่งกำเนิดวัสดุชนิดของเครื่องดึงเส้นผ่านหน้าแหล่งกำเนิดวัสดุNovember 7, 2022การวาดลวดเป็นกระบวนการประมวลผลโลหะ ในการประมวลผลด้วยแรงกดของโลหะ เหล็กจะถูกบีบผ่านแม่พิมพ์และพื้นที่ของโลหะจะถูกบีบอัดลง การใช้เทคโนโลยีนี้ช่วยให้เราสามารถทำตัวเหล็กมีคุณสมบัติที่ต้องการได้อย่างมีประสิทธิภาพมากขึ้นview
  • บทบาทของฝาครอบภายในในเตาแบบ Bell Annealing Furnaceบทบาทของฝาครอบภายในในเตาแบบ Bell Annealing FurnaceDecember 20, 2021ภาพรวมของเตาอบอนีลลิงแบบโครงหุ้มหลอดหรือ Bell Annealing Furnace คือ เตาอบที่ใช้ในการอบโลหะเพื่อสร้างความอ่อนแรงและลดความแข็งในงานเหล็กแผ่นโดยใช้โดยตรงสารที่อยู่ภายในเตาเพื่อส่งความร้อนที่ต้องการ โดยการอบโลหะด้วยเทความนี้ที่เรียกว่าการอบโครงหุ้มหลอดนั้น เขาจะใช้โดยส่วนใหญ่สำหรับการอบเหล็กแผ่นโดยตรงผ่านฝาเทอร์มอินเนอร์ของเตาอบเหล็กแบบโครงหุ้มหลอดนี้ เมื่ออุณหภูมิสูงขึ้น สารอบเหนี่ยวนำความร้อนเป็นอนุภาคเล็กๆ ที่สามารถสัมผัสกับโลหะและส่งถึงในขนาดของโลหะเองเพื่อเพิ่มความอ่อนแรงให้กับโลโคแผ่น เป้าหมายคือ การลดความแข็งและเพิ่มความอ่อน TW: Ⅰ. นิยามของเตาอบอนีลลิงในรูปแบบของหลอดหุ้มหรือเตาอบหลอดหุ้มหรือ Bell Annealing Furnace คือ เตาอบที่ใช้ในการอบโลหะเพื่อสร้างความอ่อนแรงและลดการแข็งของเหล็กแผ่นโดยการส่งความร้อนไปยังภายในเตาโดยตรงผ่านเครื่องทำความร้อนภายในเตา วิธีการอบโลหะด้วย Bell Annealing Furnace จะใช้ความร้อนจากสารเป็นตัวกลางและส่งถึงโลหะด้วยอุณหภูมิที่จำเป็น และมักใช้สำหรับการอบเหล็กแผ่นโดยตรงผ่านฝาเทอร์มอินเนอร์ของเตาอบ Bell Annealing Furnace ค้นหาเรียบเรียงและเพิ่มความอ่อนแรงให้กับชิ้นงview
  • หลักการทำงานและการประยุกต์ใช้เครื่องเสริมสายแล้วจำนวนถักหลักการทำงานและการประยุกต์ใช้เครื่องเสริมสายแล้วจำนวนถักAugust 6, 2021ไม่มีข้อความที่ต้องแปลview
  • ประเภทของเตาอบอนีลลิ่งคืออะไร?ประเภทของเตาอบอนีลลิ่งคืออะไร?November 29, 2021ไม่มีข้อความที่ต้องแปลในขณะนี้ เนื่องจากไม่มีตัวเลขหรือลิงก์เกี่ยวข้องview

:
+8613675848705

:
+8618069820917
+8613675848705
Rm512 No.:238 ChaoWang Road HANGZHOU 310005 CHINA