การใช้เครื่องเสียบสายไฟอัตโนมัติ ควรมีความระมัดระวัง

การใช้เครื่องเสียบสายไฟอัตโนมัติ ควรมีความระมัดระวัง

สินค้า

Automatic wire drawing machines have been widely used in machinery manufacturing, wire and cable, bamboo and wood products and other industries. In order to improve work efficiency and reduce the occurrence of safety accidents, Metal Tech will share the precautions for operating the automatic wire drawing machine. Let's take a look.


Before The Wire Drawing Machine Power On

(1) Operators must wear gloves to prevent the workpiece from burning fingers and affecting product quality.

(2) Before starting the machine, carefully check the air supply of the equipment, whether the air supply pipeline is leaking, and discharge the accumulated water in the air filter.

(3) Install the wire drawing abrasive belt correctly (the direction of the arrow on the inside of the wire drawing abrasive belt should be the same as the direction of the arrow on the wire drawing roller). Carefully check whether the upper and lower bearing seats and the lifting screw are well lubricated, and make sure that there is no one on the front of the discharge before turning on the machine.



When The Wire Drawing Machine Is Working

(4) After the automatic wire drawing machine is started, immediately check whether the belt swing is within the required range and whether there are other abnormal phenomena, otherwise it should be adjusted or shut down immediately.

(5) It is strictly forbidden to start the wire drawing machine and the dust collection fan at the same time, and it is strictly forbidden for the operator to leave the work post after starting the machine.

(6) It is strictly forbidden to place the workpiece directly on the conveyor belt for drawing without a pallet, and it is strictly forbidden to directly place the workpiece for drawing on a wooden pallet without a stop bar, so as to avoid damage to the conveyor belt and the workpiece flying out and hurting people.

(7) When two people are working, the operator behind the automatic wire drawing machine should not face the exit of the wire drawing machine, so as to prevent the workpiece from flying out and hurting people.

(8) The pressure adjustment of the wire drawing machine should be moderate. In general, the pressure gauge indication should be between 35 and 75. It is strictly forbidden to exceed the red line to avoid equipment or personal accidents.

(9) It is strictly forbidden to adjust the air pressure when the equipment is in normal operation, so as to avoid equipment and personal accidents caused by the loss of control of the abrasive belt.

(10) If there is any abnormal phenomenon during the operation of the equipment, it should be shut down and powered off immediately to avoid the expansion of the fault.


   

When The Wire Drawing Machine Is During The Maintenance Or Standaby

(11) When the equipment is being repaired, the main power supply should be turned off, and warning signs should be set up to prohibit operation to avoid accidents.

(12) The main power supply and compressed air should be turned off when off-duty or when the equipment is in standby for a long time to ensure the safety of the wire drawing machine equipment.


The quality of pretreatment of wire or bar by wire drawing machine is directly related to the product quality of standard parts and other metal products manufacturers. The wire drawing machine belongs to the metal product equipment industry. The metal wire drawing machine is used for the production and pretreatment of standard parts of metal products such as steel wire, various wire meshes, nails and screws.


Metal Tech Has Types of Wire Drawing Machine For Sale


straight line wire drawing machine

straight line wire drawing machine



pulley type wire drawing machine

pulley type wire drawing machine



water tank wire drawing machine

water tank wire drawing machine


vertical wire drawing machine

vertical wire drawing machine


Metal Tech sells the entire wire drawing machine line system including wire drawing machine, straightening and cutting machine, high-station wire pay off with descaling wheels, pointing machine, discharging machine, and wire drawing dies. Check if you have any interests.

บทความอื่นๆของเครื่องจักรลวดและลวดตาข่าย

  • ข้อควรระมัดระวังในการบำรุงรักษาเครื่องทำตะปูเล็กข้อควรระมัดระวังในการบำรุงรักษาเครื่องทำตะปูเล็กNovember 8, 2022ทุกครั้งที่เราใช้เครื่องทำตะปูตะเข็บพัดมันภายในของมันถูกใช้งานจนเกิดสึกหรือสึกทางขึ้นมา แม้ว่าเครื่องทำตะปูตะเข็บอาจง่ายต่อการใช้งาน ใช้พลังงานน้อย และมีเสียงรบกวนต่ำ แต่มัน ...view
  • หลักการทำงานและการประยุกต์ใช้เครื่องเสริมสายแล้วจำนวนถักหลักการทำงานและการประยุกต์ใช้เครื่องเสริมสายแล้วจำนวนถักAugust 6, 2021ไม่มีข้อความที่ต้องแปลview
  • ประเภทของเตาอบอนีลลิ่งคืออะไร?ประเภทของเตาอบอนีลลิ่งคืออะไร?November 29, 2021ไม่มีข้อความที่ต้องแปลในขณะนี้ เนื่องจากไม่มีตัวเลขหรือลิงก์เกี่ยวข้องview
  • การแนะนำหลักการทำงานของเครื่องเสริมลวดแบบเส้นตรงการแนะนำหลักการทำงานของเครื่องเสริมลวดแบบเส้นตรงMarch 13, 2023ไม่มีข้อความที่ต้องแปลโดยตรง โปรดให้ข้อความที่ต้องแปลก่อนหน้านี้ ของช่วยแปลให้คุณนะคะview
  • ชนิดของเครื่องดึงเส้นผ่านหน้าแหล่งกำเนิดวัสดุชนิดของเครื่องดึงเส้นผ่านหน้าแหล่งกำเนิดวัสดุNovember 7, 2022การวาดลวดเป็นกระบวนการประมวลผลโลหะ ในการประมวลผลด้วยแรงกดของโลหะ เหล็กจะถูกบีบผ่านแม่พิมพ์และพื้นที่ของโลหะจะถูกบีบอัดลง การใช้เทคโนโลยีนี้ช่วยให้เราสามารถทำตัวเหล็กมีคุณสมบัติที่ต้องการได้อย่างมีประสิทธิภาพมากขึ้นview
  • บทบาทของฝาครอบภายในในเตาแบบ Bell Annealing Furnaceบทบาทของฝาครอบภายในในเตาแบบ Bell Annealing FurnaceDecember 20, 2021ภาพรวมของเตาอบอนีลลิงแบบโครงหุ้มหลอดหรือ Bell Annealing Furnace คือ เตาอบที่ใช้ในการอบโลหะเพื่อสร้างความอ่อนแรงและลดความแข็งในงานเหล็กแผ่นโดยใช้โดยตรงสารที่อยู่ภายในเตาเพื่อส่งความร้อนที่ต้องการ โดยการอบโลหะด้วยเทความนี้ที่เรียกว่าการอบโครงหุ้มหลอดนั้น เขาจะใช้โดยส่วนใหญ่สำหรับการอบเหล็กแผ่นโดยตรงผ่านฝาเทอร์มอินเนอร์ของเตาอบเหล็กแบบโครงหุ้มหลอดนี้ เมื่ออุณหภูมิสูงขึ้น สารอบเหนี่ยวนำความร้อนเป็นอนุภาคเล็กๆ ที่สามารถสัมผัสกับโลหะและส่งถึงในขนาดของโลหะเองเพื่อเพิ่มความอ่อนแรงให้กับโลโคแผ่น เป้าหมายคือ การลดความแข็งและเพิ่มความอ่อน TW: Ⅰ. นิยามของเตาอบอนีลลิงในรูปแบบของหลอดหุ้มหรือเตาอบหลอดหุ้มหรือ Bell Annealing Furnace คือ เตาอบที่ใช้ในการอบโลหะเพื่อสร้างความอ่อนแรงและลดการแข็งของเหล็กแผ่นโดยการส่งความร้อนไปยังภายในเตาโดยตรงผ่านเครื่องทำความร้อนภายในเตา วิธีการอบโลหะด้วย Bell Annealing Furnace จะใช้ความร้อนจากสารเป็นตัวกลางและส่งถึงโลหะด้วยอุณหภูมิที่จำเป็น และมักใช้สำหรับการอบเหล็กแผ่นโดยตรงผ่านฝาเทอร์มอินเนอร์ของเตาอบ Bell Annealing Furnace ค้นหาเรียบเรียงและเพิ่มความอ่อนแรงให้กับชิ้นงview

:
+8613675848705

:
+8618069820917
+8613675848705
Rm512 No.:238 ChaoWang Road HANGZHOU 310005 CHINA